ATTO Technology 2600R/D Especificaciones Pagina 13
- Pagina / 72
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
4
Installation: ATTO iPBridge 2600R/D
Ethernet interface
The four independent 100/1000 Ethernet RJ45 data
ports are labeled Ethernet ports 1, 2, 3 and 4. A
separate 10/100 Ethernet standard RJ45 management
port provides monitoring and management through
telnet or ATTO ExpressNAV, a browser-based
interface.
Gb Ethernet cables must be at least CAT-5E certified.
Serial interface
The RS-232 serial port provides support for remote
monitoring and management through a command line
interface. It is set at the factory at 115,200 bps.
Reset switch
A reset switch on the back (connector) side allows
manual restart of the iPBridge using a small sharp
implement inserted into the hole at the back of the
iPBridge.
LED indicators
LED indicators viewed from the front of the iPBridge
2600R/D (see Exhibit 1.1-1):
• Bicolor Ready/Fault: off means not ready; green
on shows ready, and yellow on means fault
• Power: indicates power has been applied.
• Each Ethernet data port has two LEDs: when the
speed LED is dark it indicates 100 Mb/sec.
speed; it lights yellow for 1000 Mb/sec. speed.
The activity LED lights green to represent an
active link, blinks to show activity and goes dark
when no link is present.
• SCSI activity is indicated for each port: lighted
green means activity; off shows no activity
LED indicators viewed from the connector (back) side
of the iPBridge 2600R/D (see Exhibit 1.1-1):
• Bicolor Ready/Fault: off means not ready; green
on indicates ready, and yellow on shows fault
• Embedded in the RJ45 connector of the
management port: green on indicates a valid
link; off represents no link present
• Embedded in the RJ45 connector of the
management port: blinks yellow to indicate
management activity
• Embedded in the RJ45 connector of each
Ethernet data port: green on indicates 100
Mb/sec. speed; yellow on indicates 1000
Mb/sec. speed
• Embedded in the RJ45 connector of each
Ethernet data port: solid on represents a link is
present; blinking indicates activity, and off
shows no link is present
• SCSI activity is indicated for each port: on
indicates activity; off shows no activity.
Exhibit 1.1-1 LED indicators on the front and connector sides of the iPBridge
SCSI ports
Ethernet
management port
Ethernet data ports
LEDs
SCSI activityspeed activityReady/Fault
Reset switch
Serial port air vents
link activity
- ATTO Technology, Inc 1
- Contents 4
- Possible storage 11
- Ethernet interface 13
- Serial interface 13
- Reset switch 13
- LED indicators 13
- 2 Installing the iPBridge 14
- (supplied by ATTO) 15
- Default target node 16
- CAUTIONCAUTION 16
- Multiple target nodes 17
- Physical connections 18
- Initiator/Host to Network 18
- Installation: mapping 19
- Management page 19
- Installation: Configuration 23
- E-mail notification 24
- Remote management 25
- Firmware update 27
- Inside out method 28
- Check the host event log 28
- Visually inspect LEDs 28
- Check host versions 28
- Component check 29
- Checking the iSCSI OS driver 31
- Checking the Operating System 31
- Checking the applications 31
- Performance issues 32
- Checking the host system 33
- 6 ATTO ExpressNAV interface 34
- Browser-based GUI 35
- 6.1 ATTO ExpressNAV pages 36
- Advanced CLI configuration 37
- Restart 37
- Interfaces 39
- CLI Error Messages 41
- 7.1.1 CLI commands summary 42
- Interfaces: CLI 43
- Command Defaults Example Page 44
- 7.1.2 General use commands 46
- 7.1.3 Diagnostic commands 48
- 7.1.4 Maintenance commands 52
- from GMT in the form of 53
- The ATTO iPBridge 54
- 7.1.6 Ethernet commands 56
- 7.1.9 iSCSI commands 60
- 7.1.10 Mapping commands 62
- FibreBridge products 65
- SCSI cabling 66
- Ethernet connections 67
- Appendix C Glossary 68
- Canadian Standards 69
- European Standards 70
- Accessories 71
- Cables: RS232 71
Relacionado con productos y manuales para Redes ATTO Technology 2600R/D
Redes ATTO Technology 2400C/R/D Especificaciones
(77 paginas)
(77 paginas)
Redes ATTO Technology FC-41EL Manual de servicio
(29 paginas)
(29 paginas)
Redes ATTO Technology 4500R Especificaciones
(65 paginas)
(65 paginas)
Redes ATTO Technology 2700 Manual de instrucciones
(50 paginas)
(50 paginas)
Redes ATTO Technology UL2D Guía de usuario
(51 paginas)
(51 paginas)
Redes ATTO Technology FC-3321 Guia de preparacion
(14 paginas)
(14 paginas)
Redes ATTO Technology UL2D Guía de usuario
(71 paginas)
(71 paginas)
Redes ATTO Technology FC-3305 Especificaciones
(34 paginas)
(34 paginas)
Redes ATTO Technology UL2D Guía de usuario
(14 paginas)
(14 paginas)
Redes ATTO Technology FC-3321 Guia de preparacion
(52 paginas)
(52 paginas)
Redes ATTO Technology UL25 Manual de usuario
(91 paginas)
(91 paginas)
Redes ATTO Technology FC-3342 Manual de usuario
(76 paginas)
(76 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales