ATTO Technology Diamond Storage Array V-Class Instrucciones de operaciones Pagina 50
- Pagina / 117
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
39
ATTO Technology Inc. Diamond Storage Array Installation and Operation Manual
4.5.5 Ethernet Commands
Ethernet configuration commands configure the Ethernet and TCP/IP parameters for the Diamond
Storage Array with an optional Ethernet management services card.
EthernetSpeed
Specifies the speed of the Ethernet Network to which the
Diamond Storage Array is connected.
Choices:10 (10 baseT), 100 (100 baseT), auto
Default: auto
Set syntax: set EthernetSpeed [10 | 100| Auto]
Requires a SaveConfiguration Restart command
Get syntax: get EthernetSpeed
FTPPassword
Specifies a password of up to 32 characters for an FTP
session.
Default: diamond
Set syntax: set FTPPassword
Requires a SaveConfiguration Restart command
IPAddress
Specifies the IP Address of the Diamond Storage Array
on the Ethernet network. If DHCP is enabled, the
assigned address of the Diamond is displayed. Setting this
value always modifies the internal NVRAM value of the
IP address.If IPDHCP is enabled (see below), get
command reports current IP address assigned by DHCP
server
Default IP Address: 10.0.0.1
Set syntax: set IPAddress xxx.xxx.xxx.xxx
Requires a SaveConfiguration Restart command
Get syntax: get IPAddress
IPDHCP
Selecting DHCP allow the Diamond Storage Array to
request an IP address from the network. It requires that
the Diamond be attached to a network with at least one
DHCP server. The network must have at least one DHCP
server
Default: disabled
Set syntax: set IPDHCP [enabled | disabled]
Requires a SaveConfiguration Restart command
Get syntax: get IPDHCP
IPGateway
Specifies the IP Gateway for the Diamond Storage Array
on the Ethernet network. If IPDHCP is enabled (see
above), get command reports current IP gateway assigned
by DHCP server Must conform to AAA.BBB.CCC.DDD
standard network IP addressing.
Default: 0.0.0.0
Set syntax: set IPGateway AAA.BBB.CCC.DDD
Requires a SaveConfiguration Restart command
Get syntax: get IPGateway
IPSubnetMask
Specifies the IP Subnet Mask for the Diamond Storage
Array on the Ethernet network. If DHCP is enabled, the
assigned subnet mask for the unit is displayed. Setting
this value always modifies the internal NVRAM value of
the IP Subnet Mask.
Default: 255.255.0.0
Set syntax: set IPSubnetMask AAA.BBB.CCC.DDD
Requires a SaveConfiguration Restart command
Get syntax: get IPSubnetMask
SNMPTrapAddress
Sets up IP trap address and trap level.
Default: 10.0.0.1
Set syntax: set SNMPTrapAddress [Index:1-6] [Address:
XXX.XXX.XXX.XXX] Level:Critical |Warning
|All|None]...
.................................
Requires a SaveConfiguration Restart command
Get syntax: get SNMPTrapAddress
- Diamond Storage Array 1
- Contents 2
- Disclaimer 10
- 1.0 Product Overview 12
- Fibre Channel model 13
- SCSI model 13
- 2.0 Technical Overview 14
- ADXT Powers ATA to New Levels 15
- CAUTIONCAUTION 16
- Quick start 17
- 3.1 Components 18
- Disk drive sleds (12) 19
- System Management Card 19
- 3.2 Physical Setup 20
- 2 Gb HIC uses 22
- 2 SFPs to connect up 22
- Fibre Channel connections 23
- SCSI connections 25
- Updating Firmware 26
- Drive, sled numbering 27
- RAID Level 0 27
- 4.0 Accessing the Array 28
- In-band CLI 31
- 4.2 Serial Port Access 32
- Serial port access 33
- Ethernet protocols 35
- Accessing the Array 36
- Information 37
- 4.4.1 ExpressNAV Pages 38
- Command Line Interface 41
- Diamond Storage Array 44
- 4.5.2 General Use Commands 45
- 4.5.5 Ethernet Commands 50
- 4.5.6 Diagnostic Commands 52
- 53
- Default: 4 55
- 5.0 Configuring Drives 60
- Interleave 61
- Partitions 61
- Hot Spare sleds 61
- Enhancing performance 61
- 5.1 JBOD 62
- 24 physical drives 64
- RAID 0 subsystem example: 64
- 4 Virtual Drives 64
- 6 Virtual Drives 67
- RAID Level 5 69
- Removing RAID groups 71
- QuickRAID10 1 = LUN 1 73
- QuickRAID10 2 = LUN 1 73
- QuickRAID10 3 = LUN 1 73
- You must use a 75
- SaveConfiguration Restart 75
- 5.7 RAID Interleave 76
- RAID interleave 77
- To merge partitions 79
- 5.9 Creating Zones 80
- Other operations 83
- RestoreConfiguration default 83
- 6.0 Copying Drives 84
- Copy drives 85
- 7.0 Updating Firmware 86
- Read/Writes 89
- Diagnostic 90
- Commands 90
- Warranty 90
- Monitors, reports 91
- 8.1 Troubleshooting 92
- 8.2 Resetting Defaults 94
- Reset defaults 95
- 9.0 Hardware Maintenance 96
- Disk Drives 98
- 9.2 Optional Hot Spare Sled 100
- LUN 1 LUN 2 101
- Glossary 102
- ATTO Technology Inc 104
- Driveinfo 105
- 106
- PartitionInfo 109
- ZoneInfo 110
- Symmetric Model 111
- Asymmetric Model 112
- Appendix D Product Safety 114
- Appendix E Specifications 115
- Appendix F Part numbers 116
- Appendix G Warranty 117
Relacionado con productos y manuales para Arrays de discos ATTO Technology Diamond Storage Array V-Class
(26 paginas)Ss-cycle Para Motocicletas manuales de usuario
Empezando en F
Comentarios a estos manuales