ATTO Technology FC-3305 Especificaciones

aImportant InformationAvid recommends that you read all the information in these upgrade instructions thoroughly before installing new hardware or usi

Upgrade Instructions10 5. Click the 3D effects board set in the left pane and the right pane defines the 3D effects board being used and the type of

Determining Installed Storage Boards11Determining Installed Storage BoardsTo determine what storage boards you have in your Mac OS v9.x operating syst

Upgrade Instructions12 Installing the Mac OS X Operating SystemYou now need to install the Mac OS X operating system using the instructions provided

Removing Boards from the System13nIf your system hangs during any of the boot procedures, taking out the Avid board set might help you continue (see “

Upgrade Instructions14 Turning Off Power to the Avid PCI ExtenderTo turn off power to the Avid PCI Extender:1. Quit the Avid application.2. Shut down

Installing the Avid Boards into the System15Installing the Avid Boards into the SystemOnce the Avid software is installed you must:• Replace the neede

Upgrade Instructions16 Disconnecting the Existing 3D Effects BoardTo remove the existing 3D effects board (Genie), you need to disconnect the over-th

Installing the Avid Boards into the System17To connect the two boards:1. Carefully place the new Z6 board into the proper slot of the PCI as shown in

Upgrade Instructions18 Upgrading the Hardware to Use an Avid Symphony SystemIf you are upgrading to an Avid Symphony system you must:• Remove the old

Installing the Avid Boards into the System19Figure 3 Removing the Over-the-Top ConnectornFigure 3 shows the over-the-top connector connected to a diff

Upgrade Instructions2 ContentsSymbols and Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Before Upgrading to t

Upgrade Instructions20 To remove the old Meridien 3D effects daughter board from the digital media board:1. Place the board set on an antistatic bag

Installing the Avid Boards into the System214. Grip the boards by the PCI end and gently pull the boards apart to disconnect the connections between t

Upgrade Instructions22 5. Carefully center the cables of the new Meridien III-U 3D effects daughter board over the cable connectors on the digital me

Installing the Avid Boards into the System23Installing Boards in the G4 PlatformsTo install or replace boards in all of the G4 platforms you should:1.

Upgrade Instructions24 Table 1 lists the recommended slot locations in the 933-MHz G4 platform.Board Locations in the Dual 1-GHz or 1.25-GHz G4 Platf

Installing the Avid Boards into the System25Table 2 lists the recommended slot locations in the dual 1-GHz or 1.25-GHz G4 platform.nThe dual 1-GHz or

Upgrade Instructions26 Installing or Replacing Boards in the Avid PCI ExtenderThe following sections explain how to install or replace boards in eith

Installing the Avid Boards into the System27Figure 10 Avid PCI Extender 2 Slot Layout Table 3 lists the Meridien I/O boards and their recommended slot

Upgrade Instructions28 Removing the Top CoverTo remove the top cover on either of the Avid PCI Extenders:1. Locate a Phillips screwdriver.2. Unscrew

Installing the Avid Boards into the System29Removing and Replacing a BoardTo remove and replace an Avid board in either Avid PCI Extender:1. Make sure

Symbols and Conventions3Symbols and ConventionsIn this document, Avid drive refers to the Macintosh system’s internal hard drive. Apple Computer, Inc.

Upgrade Instructions30 Replacing the Fan Assembly (Avid PCI Extender 1)To replace the fan assembly on the Avid PCI Extender 1 chassis:1. Place the tw

Installing the Fibre Channel Driver31Installing the Fibre Channel Driver The Avid application does not automatically install the Fibre Channel driver

Upgrade Instructions32 To update the Fibre Channel adapter board firmware:1. Shut down the system.2. Disconnect the Fibre Channel cable from the Fibr

Copyright and Disclaimer33Copyright and DisclaimerProduct specifications are subject to change without notice and do not represent a commitment on the

make manage move | media™ Avid®Upgrade Instructions34

Upgrade Instructions4 Before Upgrading to the Mac OS X Operating SystemThe following sections explain what you need to know about your G4 platform and

Before Upgrading to the Mac OS X Operating System5Supported Macintosh and Avid SoftwareThe required Macintosh operating system for this release is Mac

Upgrade Instructions6 • 3D effects daughter board (connected to the Meridien II digital media board) — There are three supported 3D effects daughter b

Before Upgrading to the Mac OS X Operating System7The following SCSI storage devices are supported:• Shipping fixed-enclosure devices: - rS36/320 Medi

Upgrade Instructions8 Standalone Fibre ChannelThe following Fibre Channel storage devices are supported in the 14-drive and 10-drive Fibre Channel dis

Determining Installed Avid Boards9• Nonshipping Fibre Channel devices for the 10-drive and 14-drive Fibre Channel disk enclosure are as follows:- MEDI